X = Total real value (without the tools).Įxample: Lets assume that the castellan has 55% wall, and your commander has -80% wall, so the calculation would be: We use the same formula, but WITHOUT the tools: With the 2nd method you may result the same result: In this case 2 "scaling ladders" will do the job (!). but on spy report you see 2 "Murder Hole" tools (-50% wall each, 100% in total) - So the real value of wall without the tools is: 120% - 100% = 20% Lets assume that you see on top of the attack screen "Wall 120%". OK, lets begin with an example of the 1st method: on the top right.ĭefense tools = Additional power (for wall, gate, range).Ĭommander % = What you see on the commander info on the bottom left. always 100%Ĭastellan % = What you see on the castellan info. + + - = Xīase = Base value of wall, gate, melee and range. The "trick" here is to understand that the values (wall, moat, gate, melee, range) that you see on top of the attack screen are the values INCLUDING the tools, but we want to know how strong (well, the opposite: not so strong.) are the defenders without the tools. Using "on screen" data (without spy report) to get to the same results Using the spy report to see which defense tools are in use (remember: only on 1st wave)Ģ. It can be done in two ways (This is a little "tricky" but I will try to explain that in detail):ġ. When using "Cleaners" you may SAVE TOOLS by using the EXACT tools that are needed. Its recommended to attack those "big" targets when the "glory bonus" is activated, to double your glory. It is also good to spy ALL targets around you, to find the "big" ones. or so) it might CHANGE DEFENSE SETUP after some time. If you in doubt, re-spy just before the attack. When you spy a foreign Lord or Bloodcrow castles try to attack within a "reasonable" time frame (10 min. But, In the rare case that the defense formation has changed, attacking without tools will cause high loses. In case the formation has not changed, and still no defenders, your tools will not be used and come back after battle. (on flanks that does not have defense soldiers there is no need for cleaners - you can put your full force in 1st wave, but sometimes the defense formation might change (its very rare), however, if you want to be sure: put tools. "Cleaners" should be used only on flanks that DO HAVE defense soldiers. More ever: if you have less than 100 soldiers on a flank that has defenders, sometimes (especially when there is a high ratio of melee defenders and the defense formation is 0-0-100) you might not win this flank only on 2nd wave, so you should use tools on 3rd wave as well (don't worry: in cast that 2nd wave defeated all defenders, tools you put on 3rd wave will not be used, and will return home after battle, so you do not lose them if not used). This will clear (or "waste") the defense tools, so on all further waves (2,3,4,5,6) the defenders does not have any tools, so you can use less tools, and also it will minimize your losses during battle. This means that the defense tools are used only on 1st wave of attack, and in your further waves of attack - there are NO TOOLS LEFT for the defenders (!). Therefore it is possible to use "cleaners" → You put ONE cheap/weak soldier (like spareman) without any tools on your 1st wave of attack. formation including the tools used.įoreign lords / Bloodcrow castles has ONLY 1 tool per slot. Use "cleaners" only on flanks that have defenders (on empty flanks put full army start from 1st wave).Īlways try to spy with 100% accuracy, so you can see EXACTLY the def. put army on all 3 flanks (left, center, right) fill all waves you have (4,5,6).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |